AVALIAÇÃO DAS PROPRIEDADES FÍSICO-MECÂNICAS DE POLPAS PRODUZIDAS POR NOVAS SEQUÊNCIAS DE BRANQUEAMENTO

Ciência Florestal

Endereço:
Campus Universitário DCFL/CCR/UFSM Prédio 44 (CCR II) Sala 5241 - 2º Piso
/ RS
0
Site: http://www.ufsm.br/cienciaflorestal/
Telefone: (55)3220-8444
ISSN: 1980-5098
Editor Chefe: Elio José Santini
Início Publicação: 30/11/1991
Periodicidade: Trimestral

AVALIAÇÃO DAS PROPRIEDADES FÍSICO-MECÂNICAS DE POLPAS PRODUZIDAS POR NOVAS SEQUÊNCIAS DE BRANQUEAMENTO

Ano: 2010 | Volume: 20 | Número: 1
Autores: Cristiane Pedrazzi, Jorge Luiz Colodette, Rubens Chaves de Oliveira, Marcelo Coelho dos Santos Muguet, José Lívio Gomide
Autor Correspondente: Cristiane Pedrazzi | [email protected]

Palavras-chave: propriedades físico-mecânicas, cozimento modificado, branqueamento, ácidos hexenurônicos, celulose, eucalipto

Resumos Cadastrados

Resumo Português:

A eficiência da deslignificação com oxigênio (pré-O2) é muito baixa para polpas de baixo número kappa e que
contêm altas concentrações de ácidos hexenurônicos, pois o oxigênio não reage com esses ácidos, sendo
mínima a eliminação destes durante a deslignificação com oxigênio em simples ou duplo estágio. Neste
estudo, investigaram-se as propriedades físico-mecânicas de polpas produzidas por cozimentos cineticamente
modificados até número kappa 17 e 14 e branqueadas pelas técnicas AD(EO)D, para polpa de kappa 17 e
DHT(EPO)DP, para polpa de kappa 14. O objetivo principal do estudo foi o de avaliar as propriedades físicomecânicas
das polpas submetidas a sequências de branqueamento sem o oxigênio, no início da sequência.
Como referências, foram produzidas polpas de número kappa 17 e 14 as quais foram posteriormente
deslignificadas com oxigênio e branqueadas com sequências convencionais: A/D(EO)D, para polpa de número
kappa 17 e DHT(EPO)DP, para polpa de kappa 14. O branqueamento alternativo, sem a pré-O2, resultou em
polpas branqueadas de maior integridade que as da referência, o que foi comprovado pelos valores
significativamente mais altos de VEA (bulk), índice de rasgo, opacidade e resistência à passagem de ar (RPA)
da polpa fracamente refinada (polpa para produzir papel tissue). Por outro lado, a alta integridade das fibras
oriundas das polpas branqueadas por processos alternativos diminuiu suas conformabilidades e colapsabilidades,
com consequente diminuição do índice de tração da polpa fracamente refinada. Porém, mediante um refino
mais intenso (polpa para produzir papel de imprimir e escrever – P&W) o índice de tração foi recuperado. A
alta integridade das polpas branqueadas sem a pré-O2 dificulta o seu refino. Para alcançar o grau de drenagem
de 35oSR com as polpas provenientes dos processos alternativos de branqueamento, foi necessário aplicar
cerca de 30% a mais de energia em relação à referência.



Resumo Inglês:

The efficiency of oxygen delignification is very low for pulps of low number kappa and with high concentrations
of hexenuronic acids, therefore the oxygen does not react with these acids, so being minimum the elimination of these during the oxygen delignification (pre-O2) in simple or double stage. In this study, the physicalmechanical
properties of pulp of kappa number 17 and 14, produced with modified cooks and with the
application of AD(EO)D techniques for pulp of kappa 17 and DHT(EPO)DP for pulp of kappa 14 for the
bleaching up to 90% ISO, had been investigated. The main objective of this study was to evaluate the physicalmechanical
properties in pulps submitted to the bleaching sequences without oxygen in the beginning of the
sequence. As references, cooks had been carried until numbers kappa 17 and 14, oxygen delignification and
conventional bleaching for sequences A/D(EO)D for pulp of kappa 17 and DHT(EPO)DP for pulp of kappa
14. The alternative bleaching, without pre-O2, resulted in bleached pulps with bigger integrity that of the
reference, what it was confirmed by the values significantly higher of bulk, tear index, opacity and air resistance
of the pulp weakly refined (for tissue papers). However, the high integrity of the fibers from pulps bleached
with alternative processes lowered their conformabilities and collapsibility, with consequent reduction of
tensile index of the pulp weakly refined. Therefore, with more intensive beating (for printing and writing
papers), the tensile index was recovered. The high integrity of the bleaching pulps without pre-O2 makes
beating difficulty. To reach the draining degree of 35°SR with the pulps proceeding from alternative processes
of bleaching, it was necessary to apply 30% more energy than the reference.